Welding)이라고 할 수 있다.
금속을 접합하는 방법은 크게 두 가지로 기계적 접합과 금속학적 접합법으로 분류한다. 기계적 접합이란 접합면에 국부적인 소성변형을 주는 것으로 볼트이음, 리벳이음, 가열끼우기 등이 있으며, 금속학적 방법(또는 야금학적 방법)이란 접합면에 열같은 에너지를 가하여 국
Deformed Bar)
ㆍ인장력이 큰 철근으로 HD로 표시.
ㆍ일반적인 철근에 비해 강도가 큼.
2.철근공사
2. 강재의 종류
4. 피아노선 및 경강선 (KS D309, KS D3510)
ㆍ피아노선은 인장력이 아주 큰 중 경강선이고
프리스트레스트콘크리트에 쓰인다.
2.철근공사
2. 강재의 종류
5. 용접철망(Welding Wire Fabric)
ㆍ철
6.1.1 철근의 종류
원형 철근(round bar)
마디와 리브가 없는 보통의 철근은 원형철근.
원형철근의 표준길이는 4.5m에서 5.0, 6.0, 6.5, 7.0, 8.0, 9.0m로 되어 있으며, 지름은 9mm
에서 12, 16, 19, 22, 25, 28, 32mm가 일반적으로 사용.
이형철근(deformed bar)
공칭지름은 D로 표시하며, 부착
16장 판재 성형과 장비
16.1 서론
? 판재성형 : 판재를 전단, 굽힘, 인장 등의 방법으로 모양을 변형시키는 가공
- 대부분의 판재 성형은 상온에서 이루어짐
? 프레스작업(=스탬핑) : 가장 일반적인 판재 성형
16.2 전단
: 큰 판재로부터 원하는 치수로 절단된 블랭크로 만드는 작업
? 전단작업의 주
Chapter 21 기계 가공의 기초
21.1 서론
? 절삭공정
: 칩의 생성에 의해서 공작물의 다양한 표면으로부터 재료를 제거하는 것
? 절삭공정의 종류
1. 선삭 (turning) - 공작물이 회전, 절삭 공구가 횡축 방향 이동
2. 절단 (cutting off) - 공구가 반경 방향으로 이동, 가공물 오른쪽 부분 분리 절단
3. 평밀링 (slab
1 Introduction
When designing an aircraft, it’s all about finding the optimal proportion of the weight of the vehicle and payload. It needs to be strong and stiff enough to withstand the exceptional circumstances in which it has to operate. Durability is an important factor. Also, if a part fails, it doesn’t necessarily result in failure of the whole aircraft.
The main sections of an aircra
1. Pump에서의 Cavitation (공동현상) 에 대하여 기술하고 이로 생길 수 있는 문제점과 그 방지책에 대해 논하시오
- Cavitation이란
유체가 넓은 유로에서 좁을 곳으로 고속 유입하거나 벽면의 요철, 만곡부 등으로 흐름이 직선적이지 못할 때 유체는 저압이 되고 포화증기압보다 낮아지면 기화되어 기포가
The remorseless drought had lasted now for ten million years, and would not end for another million. The reign of the terrible lizards had long since passed, but here on the continent which would one day be known as Africa, the battle for survival had reached a new climax of ferocity, and the victor was not yet in sight. In this dry and barren land, only the small or the swift or the fierce could
We are moving through a small airfield full of parked light planes. There are no people around. We move through the cluster of planes towards a hangar on the edge of the field.
INT. HANGAR - DAY
We are still moving through light planes, but now we are inside the hangar. Some of the planes have their engine covers open, parts strewn around. Others are partially covered with tarps or have sections